Wuxi Senjie PVC wood plate production line

A brief introduction of.PVC wood plastic foam sheet production line
1., screw feeding machine, feeding speed per hour up to 1000kg, to ensure the stability of the entire production line.
2. host
1) the main hopper is sealed, which can effectively reduce the dust in the workshop. The bottom of the hopper is provided with a discharge opening, and if the raw material or the formula has the quality problem, the raw material can be directly discharged from the material opening to reduce unnecessary loss.
2) the main structure adopts the screw with more reasonable structure, which ensures the plasticization and improves the output. According to the requirements of the customer's products, the screw structure of the cylinder can be adjusted to meet the needs of different formulations.
3) the main electrical control meter is mainly digital display, and each parameter is more intuitive.
4) the main machine can control the speed of discharging, so that the product is even and even. Small weight error.
3. setting table
1) the setting platform adopts the square pipe pillar structure, each set mold has the support, the three point localization. The bearing capacity of the setting table is ensured, and the deformation is not easy to be deformed.
2) the hydraulic cylinder adopts two segments of hydraulic pressure, and the shaping platform can move before and after the speed regulation. It is automatically close to the die at close to the mouth to avoid the impact of the opposite die and cause the damage of the die. At the same time, the cylinder can automatically lock the mold, automatically maintain pressure, fill pressure, and reduce energy consumption.
3) the pipeline and oil circuit in the setting station are arranged clearly.
4. tractor
1) the traction machine adopts nine roller traction, which increases the traction force and is not easy to skid. The first set of rollers can be changed into a carved roller, and the large plate with the pattern on the surface can be directly printed online.
2) the traction machine adopts chain drive, compared with the gear drive, it has more power transmission, and it is not easy to skid. It provides a guarantee for the continuous and stable production of the equipment.
3) controlled by a single gas tank, the upper roller rises and falls, and the roller rises and falls to keep synchronization.
5 slitting
1) the saw blade and the surface of the board are always kept at 90 degrees right angle, equipped with dust collection system. The filter core in the recovery system can separate dust and air well, and the dust in the air can not be seen under the sunlight. Provide a guarantee for the good operation of the equipment and the tidiness of the workshop environment. Many manufacturers use self-made cloth bags to collect dust. Because of the defects of bag density and air separation, the effect of dust recovery is not obvious.
6. crosscut
1, the cross cutting uses linear guide rail to move, and guarantees the verticality of the four sides of the plate. Also equipped with a dust recovery system.
2) cutting part adopts OMRON programmable control system, interface operation uses touch screen design. Laying a good foundation for the fixed length, fixed width and cutting of the plate.
Two. Functional characteristics compared with similar manufacturers, our company's products have the following characteristics:
The 1. screw feeding machine adopts air separation system to realize the dust-free feeding.
2., choose more reasonable foam screw, extrusion stability, foam evenly.
3 with the well-known Hongda mould mould factory cooperation, product quality and stability.
4. hydraulic cylinder adopts two segments of speed, automatically realize fast and slow travel.
5., nine groups of rubber roller traction, traction power, not easy to slip.
6 rip cross cut is equipped with a dust collection first domestic separation system, to achieve the full range of clean production.
7. the cross cutting adopts linear guide rail to move back and forth to ensure the squareness of the plate.
8. cross cutting adopts the original OMRON programmable control system in Japan. The man-machine interface is displayed by LCD touch screen, and the parameters are adjusted conveniently and visually.
9., the main electrical components all adopt Japanese famous brand products.
Three. Service
For the first time and customers we can provide a series of services, including planning, transformer plant considerations, raw material procurement, budget etc.. When debugging, products can be produced according to customer requirements, and provide personnel training. Welcome to visit our factory.